<button id="zn9je"><acronym id="zn9je"></acronym></button>
    1. <dd id="zn9je"><track id="zn9je"><video id="zn9je"></video></track></dd>
    2. <nav id="zn9je"><big id="zn9je"><noframes id="zn9je"></noframes></big></nav>
      <em id="zn9je"></em>
      <th id="zn9je"><track id="zn9je"><dl id="zn9je"></dl></track></th>

    3. <dd id="zn9je"><pre id="zn9je"></pre></dd>
    4. <button id="zn9je"><tr id="zn9je"><kbd id="zn9je"></kbd></tr></button>

      WELCOME TO WUXI CITY HUIFENG ELECTRONIC.CO.LTD!
      National Consultative Hotline 0510-85310683

      PRODUCT CENTER

      Contact US

      Address:No.20 16-3 plot,5th,Shuofang Industrial Concentrated Zone, New District, Wuxi 214142, Jiangsu, P.R.China
      TEL:0510-85310683
      Website:www.yoginisyoga.com
      Fax:0510-85310683
      Mailbox:tdh@hfpzt.com
         wxhfscb@163.com

      Attention point of piezoceramic welding

      publish:HUIFENG  time:2017年06month09day

      What is the vibration detection circuit of a piezoelectric ceramic chip? What should be paid attention to in the process of welding? In addition, what is the relationship between the waveform and time of electricity generated by piezoelectric ceramics and the force? Now that these problems have been raised, the following, to solve it immediately, I hope you can get some new harvest and inspiration.
      1. what is the vibration detection circuit of the piezoelectric ceramic chip?
      The vibration detection circuit of piezoelectric ceramic chip is not complicated. It only needs to connect two electrodes to the oscilloscope. However, it should be noted that the voltage at both ends of the ceramic sheet is MV grade. Moreover, if the amplitude of the signal is too low, the low noise operational amplifier can be used to amplify the signal for observation.
      2. what should we pay attention to during the welding process of piezoelectric ceramics?
      There are some points for attention in the welding of piezoelectric ceramics.
      The welding temperature should not be too high; in the welding time, it is not suitable for the process, otherwise, it will affect the quality of the welding, and then affect the use effect of the piezoelectric ceramic. In general, it takes only a few seconds to weld.
      3., what is the relationship between the waveform and time of electricity generated by piezoelectric ceramics and the force?
      In particular, if it is a periodic changing force that continues to act on a piezoelectric ceramic piece, then the piezoelectric ceramic will continue to generate electricity, and its waveform is closer to the sine wave. If it is a momentary force, then the wave is approaching the pulse.
      The above problems are all from the web product of the piezo ceramic piece, which are extended, and it is not before, so I hope you can take it seriously and carry on it so that you can understand and master it in time. In this way, even in practice, we can deal with it calmly and solve it satisfactorily, so as to avoid unnecessary problems or troubles.

      国语少妇高潮对白在线_荡女小茹…用力_无码人妻一区二区三区免费手机_青春男同xvideos gay
      <button id="zn9je"><acronym id="zn9je"></acronym></button>
      1. <dd id="zn9je"><track id="zn9je"><video id="zn9je"></video></track></dd>
      2. <nav id="zn9je"><big id="zn9je"><noframes id="zn9je"></noframes></big></nav>
        <em id="zn9je"></em>
        <th id="zn9je"><track id="zn9je"><dl id="zn9je"></dl></track></th>

      3. <dd id="zn9je"><pre id="zn9je"></pre></dd>
      4. <button id="zn9je"><tr id="zn9je"><kbd id="zn9je"></kbd></tr></button>